拋光樹脂（電子廠半導體超純水）原裝進口
一.簡要介紹：
（1）Tulsimer®MB-106 UP 是由核子級強酸型陽離子Tulsimer®T-46 及核子級強堿型陰離子Tulsimer®A-33 以1:2 體積比的劑量比例，預先混合的混床級離子交換樹脂，專門提供給需要高純水系統拋光用。
（2）Tulsimer®MB-106 UP 是專門用于超純水的**段的拋光處理。
（3）Tulsimer®MB-106 UP 適合用于電子產業，生產半導體及映像管產業等需要超純水的行業。具有高的交換容量及優越的物理特性。
二.產品特性：
核子級拋光樹脂Tulsimer® MB-106 UP，產水18.2兆歐超純水制備，性能對應羅門6040拋光樹脂。主要優勢是產水量大，行業內口碑較佳，具有超高性價比。
三.基本參數：
表1-1 Tulsimer® MB-106 UP 基本特性
|
型式 (Type) |
T-46 (陽) 強酸性陽離子交換樹脂 (Strong acid Cation exchange resin) |
A-33 (陰) 強堿性陰離子交換脂 (Strong base Anion exchange resin) |
|
主體結構 (Matrix Structure) |
苯乙烯 (Cross linked polystyrene) |
苯乙烯 (Cross linked polystyrene) |
|
功能基 (Functional Group) |
硫酸基 (Sulfonic acid) |
季胺 (Quaternary ammonium Type I) |
|
物理性貭 (Physical Form) |
球狀顆粒 (Moist spherical beads) |
球狀顆粒 (Moist spherical beads) |
|
離子型式 (Ionic form supplied) |
氫 (Hydrogen) |
氫氧 (Hydroxide) |
|
粒徑范圍 (U.S.mesh in wet) |
16 to 50 |
16 to 50 |
|
粒度范圍 (Particle Size) |
0.3 to 1.2 mm |
0.3 to 1.2 mm |
|
微粒含量 (Fines Content) |
穿過 US 50 Mesh 小于 0.5% (Less Than 0.5% passing through 50 U.S.mesh) |
穿過 US 50 Mesh 小于 0.5% (Less than 0.5% passing through 50 U.S.mesh) |
|
總交換容量 (Total Exch. Capacity) |
1.8 meq/ml minimum of 99% in hydrogen form |
1.0 meq/ml minimum of 90% in hydroxide form and less than 1% in chloride form |
|
PH 范圍 (pH Range) |
0 to 14 |
0 to 14 |
|
允許溫度 (Temp. Stability) |
120°C |
60°C |
|
溶解率 (Solubility) |
Insoluble in all common solvents |
Insoluble in all common solvents |
|
溶出有機物 (Organic leachable) |
Less than 0.2 mg KMNO per ml of wet resin |
Less than 0.2 mg KMNO per ml of wet resin |
|
密度 (Backwash settled density)
|
Approx.750 gm/liter |
|
|
不純物 (Impurities) |
Fe=50 ppm(max) Cu=50 ppm(max) Pb=50 ppm(max) |
Fe=50 ppm(max) Cu=50 ppm(max) Pb=50 ppm(max) |
|
球粒強度 (Bead strength) |
Avg. not less than 500g/bead by Chatillon test (ASTM Standard) |
Avg. not less than 300g/bead by Chatillon test (ASTM Standard) |
|